DEFY
DEFY Solid Color Wood Stain
- Toughness and durability of zinc nanoparticle technology.
- 7 pre-mixed grab and go colors.
- Protects wood from UV rays.
- Can be used on both horizontal and vertical wood surfaces.
- Easy soap and water clean-up.
DEFY Solid Color Wood Stain is a durable acrylic, opaque wood finish that protects against the damaging effects of the elements, on all wood surfaces. This water-based product provides a beautiful matte finish, fortified with transparent zinc nanoparticles. These zinc nanoparticles are like sunscreen for your wood. They provide extreme protection by blocking out the sun's harmful UV rays, as well as resisting stains caused by mold and mildew.
DEFY Solid Color Wood Stain can be used all wood types including pressure treated lumber, pine, cedar, redwood, mahogany, Ipe and all other natural wood surfaces. Product can be used on interior, exterior, horizontal, and vertical wood surfaces including decks, fences, wood siding, log homes, and outdoor furniture.
Note: Actual color may vary from on-screen representation.
Warning: This product can expose you to Benzophenone, which is known to the State of California to cause cancer, and Methanol, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
More Information
Stain Colors & Sizes
Defy Solid Color Wood Stain is available in seven (7) pre-mixed colors, White, Stone Gray, Taupe, Light Walnut, Dark Walnut, Dark Cocoa, and Barn Red. All colors are available in one-gallon plastic wide-mouth jugs.
Surface Preparation
Allow new wood to weather for 3 to 6 months to adequately dry out prior to application. Kiln dried lumber can be stained immediately.
Clean & Brighten
All wood surfaces must be clean, porous, and visibly dry before applying DEFY Solid Color Wood Stain.
For best results, use DEFY Wood Cleaner to remove dirt, mill glaze, mold or mildew stains, graying and other foreign matter that might block surface pores and interfere with product penetration. Rinse thoroughly using a garden hose or pressure washer.
While surface is still wet from cleaning or stripping, use DEFY Wood Brightener to neutralize the wood, restore the wood to its natural color, and open the pores of the wood, allowing the stain to be more easily absorbed.
APPLICATION
Weather Conditions: Surface and air temperatures should be between 45°F and 95°F. Avoid application in direct sunlight. Do not apply to wet or water saturated surfaces, or when rain is expected within 12 hours. Stain may be applied to wood surfaces the same day as cleaning and brightening as long as surface is visibly dry before staining.
Mix Well: Shake or stir contents before and periodically during use. To ensure absolute color uniformity from container to container, mix at least one third of the product from a used container with the contents of a new one. Do not thin product.
Protect Adjacent Areas: Protect all adjacent non-targeted surfaces such as siding, windows, masonry, plant life, etc. from overspray and runoff. Immediately remove overspray with soap and water. Overspray that is allowed to dry will be difficult to remove.
Use the Right Equipment: Hand brushes should be high quality nylon or polyester. A paint roller may also be used. If using an airless sprayer, use the lowest pressure that achieves a uniform spray pattern to minimize fogging and overspray when spraying.
Apply: Most applications require 2 coats of product be applied, waiting for the first coat to dry before applying the second.
Drying Time: To touch, 1-2 hours depending on temperature and humidity. Allow 24 hours for deck to completely cure before using. High humidity and lower temperatures can greatly increase dry time.
Clean-Up: Clean tools and equipment immediately with soap and water.
Coverage: One gallon will cover approximately 200-300 sq. ft. per coat, depending on wood texture and porosity.
Click here for Product Data & Safety Sheets.
DEFY Solid Color Wood Stain is a durable acrylic, opaque wood finish that protects against the damaging effects of the elements, on all wood surfaces. This water-based product provides a beautiful matte finish, fortified with transparent zinc nanoparticles. These zinc nanoparticles are like sunscreen for your wood. They provide extreme protection by blocking out the sun's harmful UV rays, as well as resisting stains caused by mold & mildew. DEFY Solid Color Wood Stain can be used all wood types including pressure treated lumber, pine, cedar, redwood, mahogany, Ipe and all other natural wood surfaces. Product can be used on interior, exterior, horizontal, and vertical wood surfaces including decks, fences, wood siding, log homes, and outdoor wood furniture.
SURFACE PREPARATION
Allow new wood to weather for 3 to 6 months to adequately dry out prior to application. Kiln dried lumber can be stained immediately.
CLEAN: All wood surfaces must be clean, porous, and visibly dry before applying DEFY Solid Color Wood Stain. For best results, use DEFY Wood Cleaner to remove dirt, mill glaze, mold or mildew stains, graying and other foreign matter that might block surface pores and interfere with product penetration. Rinse thoroughly using a garden hose or pressure washer.
BRIGHTEN: While surface is still wet from cleaning or stripping, use DEFY Wood Brightener to neutralize the wood, restore the wood to its natural color, and open the pores of the wood, allowing the stain to be more easily absorbed.
APPLICATION
WEATHER CONDITIONS: Surface and air temperatures should be between 45°F and 95°F. Avoid application in direct sunlight. Do not apply to wet or water saturated surfaces, or when rain is expected within 12 hours. Stain may be applied to wood surfaces the same day as cleaning and brightening as long as surface is visibly dry before staining.
MIX WELL: Shake or stir contents before and periodically during use. To ensure absolute color uniformity from container to container, mix at least one third of the product from a used container with the contents of a new one. Do not thin product.
PROTECT ADJACENT AREAS: Use plastic, cardboard, and/or drop cloths to protect all adjacent non-targeted surfaces such as siding, windows, masonry, plant life, etc. from overspray and runoff. Immediately remove overspray from non-targeted areas with soap and water. Overspray that is allowed to dry will be difficult to remove.
USE THE RIGHT EQUIPMENT: Hand brushes should be high quality nylon or polyester. A paint roller may also be used. If using an airless sprayer, use tips between .013 and .015, and use the lowest pressure that achieves a uniform spray pattern to minimize fogging and overspray when spraying. To insure a uniform finish, it is always best to back brush when spraying.
APPLY: Most applications require 2 coats of product be applied, waiting for the first coat to dry before applying the second.
DRY TIME: To touch, one to two hours depending on temperature and humidity. Allow 24 hours for deck to completely cure before using. High humidity and lower temperatures can greatly increase dry time.
CLEAN-UP: Clean tools and equipment immediately after each use with soap and water.
COVERAGE: One gallon will cover approximately 200-300 sq. ft. per coat, depending on wood texture and porosity.
PRECAUTIONS
Keep out of reach of children. Avoid contact with eyes, skin, and clothing. Wash hands and exposed skin after use.
FIRST AID
IF INHALED: Remove to fresh air. Get medical attention if symptoms persist. SKIN CONTACT: Wash with soap and water. Get medical attention if irritation develops and persists. EYE CONTACT:Flush with water for several minutes. Get medical attention if irritation persists. IF SWALLOWED: DO NOT induce vomiting. Rinse mouth with water. Get medical attention if symptoms develop. For additional information for this product, consult the Product Data Sheet.
KEEP FROM FREEZING
VOC CONTENT < 250 g/L
SIMPLE
- DEFY not only stains the wood, but it also seals it against water penetration
- DEFY stains can be applied to visibly dry wood or wood that is slightly damp. This makes it possible to clean, brighten and stain all in one day.
- DEFY stains are penetrating stains that soak into the wood pores to form a strong, long-lasting bond.
- No messy solvents needed! Clean-up is easy with just soap and water.
BEAUTIFUL
- DEFY offers clear, semi-transparent, and solid stains in a variety of colors that not only protect but beautify your wood.
- DEFY stains are available in flat, natural-looking finishes as well as finishes with a satin sheen (DEFY Ultra).
DURABLE
- DEFY stains are formulated with the latest technology, combined with high-quality ingredients that create a lasting finish that is not prone to peeling, premature fading, or graying.
- DEFY stains offer weather protection from the sun, rain, and snow.
DEFY stands behind the integrity of our products. If you are not satisfied with the performance of this product, and provide that you have followed label instructions, return the unused portion with a proof of purchase for refund or replacement of product.
This guarantee does not include the cost of labor for removal or application of the product.
FAQs
When you've been making wood stain products as long as we have, you get used to answering similar questions. So we've gathered some of our most frequently asked questions for you here.
If you can't find the answer you're looking for below, we have more FAQ's here. Our blog is also has helpful resources and videos designed to help homeowners with every type of wood stain project.
CLEANING & PREPARATION
The answer varies based on the current condition of your wood. If you do decide to pressure wash your deck, use pressure between 1,000 or 1,200 psi. Also be sure to work with the grain and never against it, as it will cause damage to the wood's surface and splinters.
If you don't have easy access to a pressure washer or have to pay to rent one, we recommend DEFY Wood Cleaner instead. It's easy to use and will clean deep into the wood, which makes your next coat of wood stain more effective and more beautiful.
If you are using an oil-based stain, definitely. You can use DEFY stains, which are water-based products, even when the surface is slightly damp.
With oil based stains, wood must be bone-dry before you can begin staining. However, DEFY stains are water-based, so you can use them even when the surface is slightly damp.
If your wood is in constant shade and moisture is present often, you might never be able to prevent mold and mildew completely. However, you can improve your chances by keeping your deck cleaned and sealed with professional grade stains like DEFY Extreme, DEFY Ultra, and DEFY Solid stains. All 3 of these DEFY stain products contain zinc nano-particles to resist mold/mildew growth. Zinc is naturally resistant to mold & mildew.
Use a diluted bleach solution to clean it off. Mix DEFY Wood Cleaner with water (five parts water to one part cleaner), spray it on, let it set for five or ten minutes, and rinse it off. To prevent it from coming back, stain your deck with DEFY Ultra, Solid, or Extreme Wood Stain for the ultimate mold and mildew protection.
TOOLS & APPLICATION
The best tool for the job varies by the type of job. For decks, the quickest and easiest method to apply DEFY deck stain is with a "car wash" brush. Some have handles and some are handheld and they can be found in most home improvement stores.
You can, but we don't recommend it. Paint rollers were designed for thick paint, not water-based wood stains. Using a roller will often simply push the stain around on the surface and not force it into the pores. It can also leave a stipple effect in the finish when the stain has dried.
When using a semi-transparent DEFY stain (Essential, Extreme or Ultra), only apply as much stain as the wood can absorb easily. If any puddles form during your staining process, be sure to brush them out to disperse the puddle.
DEFY Essential and Extreme stains have a flat finish, so if a gloss has formed on the surface the stain has been over-applied. Over time, it will be likely to peel. Even after two coats, your deck should still have a flat finish.
With DEFY Ultra stains, two coats will result in a satin finish. One coat will appear flat. A glossy appearance, would still indicate an over-application.
This can vary slightly based on where you live, but typically the Spring and Fall offer the easiest conditions to work in. Below 80° is ideal and regardless of the season, it's best to stay out of direct sunlight because it can cause the stain to dry too quickly.
CARE & MAINTENANCE
We know it's easier NOT to stain your deck, but we've designed DEFY wood stains to be the next easiest thing! Leaving your deck untreated, means you'll be building a new deck in a few years and that's much more expensive than protecting the one you've already got.
Your home's outdoor spaces are extension of your life and they deserve both beauty and protection. DEFY wood stains will help protect your investment from UV rays, stains from mold and mildew, and moisture. Restore and extend the life of your deck with DEFY.
That’s easy! Clean your deck with DEFY Wood Brightener, which will give it a boost in appearance. You can also apply one, light coat of new stain once you've brightened.
Yes, DEFY Composite Deck Sealer works well on most composite wood surfaces. Just follow all of the directions in the same way that you would if you were staining regular wood and you'll love the results!
Our Recommended Steps for Maximum Performance
Better Wood Starts here
RESTORE & PROTECT WITH DEFY
DEFY Project Gallery
We Can Help
Not Sure If This Stain Is RIGHT FOR YOU?
Wondering which DEFY products it takes to
complete your project?
Answer just a few questions
(it takes less than a minute) and we can tell you exactly what you need to get the job done.